New Products

New for 2017 is our Savage Mower


 


 

TECHNICAL SPECIFICATIONS FOR TOOL CARRIER AND ATTACHMENTS

 

This integrated tool carrier is to replace the typical farm tractors when used as a combined unit for roadside maintenance mowing.

 

Weight with no attachments:  12,070 pounds

Max height:  110 inches

Max width:  100 inches in boom mower configuration and 88 inches for side mower

Max length:  200 inches with no attachments

Ground clearance:  lowest point is 18 inches

Max gross weight with attachments:  19,500 pounds

Operating speed: 0 to 25 mph in road speed selection and 0 to 5 mph in work

Mainframe: Rigid frame with inch steel plates 42 inches wide and 172 inches long with 1 inch cross members for attaching counter weight and side mounted cutters.  A protected 48 gallon fuel tank is embedded in the frame.

Engine:  Perkins 1104DE4TZ Tier 3 turbocharged intercooled diesel 125 hp at 2200 rpm

Engine monitoring:  Console mounted electronic screen display for engine rpm, engine coolant temperature, voltage, oil pressure, fuel quantity, groundspeed, rear axle centering sensor, and cutter hydraulic pressure and joystick functions.

Axles:  Two Comer 238 steerable drive axles each rated 22,480 pounds dynamic foot pounds.  Front axle is rigid mounted and rear is pivoted. An operator joystick stabilizes hydraulic cylinders on each side of rear axle.

Tires:  13.00 x 24 G3/L3 tread 12 ply mounted on 9 x 24 special offset wheels with 5/8 inch thick steel centers

Steering:  Front, both and crab operator selectable with rear axle centering sensors.

Hydraulic Tank:  Baffled 78 gallon 7 gauge steel tank with a 30 hp oil cooler, sight gauge for temperature and quantity and two 10 micron canister type filters.

Hydraulic Drive:  Eaton/Linde HPV hydrostatic system

Cutter Drive Pumps:  Two stage 35 gpm at 3000 psi open center cast iron gear type 

Cutter Manifold: Two electronic on/off with blade braking and with operator console pressure monitoring

Attachment controls:  Six function electronic joystick for side mounted cutter and push button for front hitch attachments.

Cab:  Insulated operator cab protected under ROPS with heating and air conditioning and independent fresh air fans. Spring cushioned operator seat that can swivel 20 degrees left and right. The seat has adjustable arm rests. Right side window is 3/8 inch thick bronze tinted abrasion resistant polycarbonate.  The rear, left rear side and left entrance door is made of inch thick bronze tinted abrasion resistant polycarbonate.  The windshield is made of inch thick auto safety glass.  There is a two speed windshield wiper.  There is an AM/FM stereo receiver with DVD player, blue tooth, GPS and back monitor.

Lighting:  Two 45 watt LED forward work lights and one 45 watt LED rear work light, 28 inch LED flashing amber light bars on front and rear of cab, LED stop and turn signals.

Front Attachment Hitch:  Skid steer type quick hitch rated 5,400 pounds and has 21 inches of travel.  It has a 35 gpm at 3000 psi power point.  It has connections for a left and right control cylinder.

ROPS was certified to ISO 3471:2008 (E) in March 2016.

 


 

BOOM MOWER SPECIFICATIONS

Reach Out from Centerline:  22 feet and 24 feet

Reach Up:  21 feet and 23 feet

Ax Cutterheads

     60-inch cut ax head with 1-1/4 inch thick T-1 steel two position blade holders

     50-inch cut ax head with 1 inch thick T-1 steel two position blade holder

     Blades are 5/8 x 5 inch double edge

     Replaceable 3/8 x 2-1/2 inch T-1 steel full length skids

     Operator controlled hydraulic deck door

     90 degree deck swivel to allow legal transport of 100 inches total width

     Deck is made of 10 gauge A606 steel reinforced and with inch sides

     Operating rpm is 1250 for the 60 inch and 1950 for the 50 inch

     Direct drive spindle is made of heat treated 4140 tool steel and is 7.5 inches od, has

          2-5/8 inch id top bearing and a 3-5/8 inch id bottom bearing

Optional heads include 62 inch cut grass flail, 48-inch cut flail ax, 54-inch cut twin blade  

           saw and 22-inch ditcher

Boom Cylinders are all welded and rated at 3000 psi

Main Boom is 8 x 6 x wall steel tube with inch thick T-1 steel attachment points

Outer Boom is 6 x 8 x wall steel tube with inch thick T-1 steel attachment points

Swivel has a 2-1/2 inch solid class L shafting nitrided king pin with Teflon impregnated bushings.  It has 135 degrees of total travel with 90 degrees rearward and 45 degrees forward.

 


     

ROTARY SIDE MOWER

Width of cut:  60 inches

Blade holder: 1 inch thick T-1 Steel with six positions

Deck:  inch thick reinforced top and wide inch thick sides

Guarding:  Chains on front and belt on rear

Skids: 3/8 x 2-1/2 thick full length T-1 steel

Operating rpm is 1250

Direct drive spindle is made of heat treated 4140 tool steel and is 7.5 inches od, has a

     2-5/8 inch top bearing and a 3-5/8 inch bottom bearing

Deck operating range is 90 degrees up and 60 degrees down.

Cast iron gear type motor

Lift cylinder is 3 x 10 tie rod 3000 psi rated cylinder

Tilt cylinder is 3.5 x 10 tie rod 3000 psi rated cylinder

 


 

FLAIL SIDE MOWER

Width of cut:  62 and 74 inches

Skids:  3/8 x 2-1/2 inch full length T-1 steel

Ground roller:  6-inch diameter with height adjustment at 1 to 5 inches

Cuttershaft:  6-inch diameter operating at 2250 rpm

Operating arc:  90 degree up to 60 degrees down

Belt driven with automatic tensioner by cast iron gear type motor

 


 

FRONT ROTARY CUTTER

Twin spindle gear box rotary cutter has a 94 inch cut.  Two position 1 inch thick blade

     holders with x 4 grass up lift blades.  Hydraulic cast iron gear motor to drive gear

     boxes at 1250 rpm. Replaceable skids are 3/8 x 2-1/2 inch full length T-1 steel.

Deck construction is made of 7 gauge steel reinforced. 


 

 

FRONT GRASS FLAIL

Front grass flail has an 88-inch cut and is hydraulic cast iron gear motor that will spin the

     6-inch diameter cuttershaft 2250 rpm.  The motor will drive a belt with an

          automatic tensioner.

     The ground roller will be adjustable with operating height of 1 to 5 inches.  It has   

           3/8 x 2-1/2 inch replaceable full length T-1 steel skids.


 




 

Home

Boom Mowers

Side Mowers

Flail Mowers

Cutter Heads

New Products

About Us


Telephone:
(423) 663-3723 
Copyright  2017
Chambers American Products, Inc.
 
All Rights Reserved
Fax:
(423) 663-3655 
 
Web Design by: Carissa Chambers 
Email: 
capmowers@highland.net